Advertisement
English transcript
Hello everyone...
and welcome to this tutorial...!
this tutorial is for making the MQ-1 Predator and solidworks...
now, we will make the predator and different parts...
first, we will start with body
and... using blue prints and surfacing tools mostly...
we will make the body of predator...
afterwards...
we are going to model the Hellfire Missile...
after that...
we are going to make the launcher for the Hellfire Missile...
after that...
we will make the...
... targeting system for the MQ-1 predator...
this is also in two parts...
here we have the Turret...
for the MTS... and then the MTS itself...
fine... we are going to assemble all of these components...
and end up with this assembly...
so... let's begin...
right, let's start with the body of the UAV...
open a new part...
and select the correct units...
now the first that we will have to do...
... is to place the blue prints on these three planes...
let's start with the top one...
open a new sketch in the top plane...
and go to tools... sketch tools...
and sketch pictures...
put blue print...
... and select yes
now we need a reference dimension, to be able to scale the blue print...
and we will use this dimension of 8.22 meters...
... as a reference for scaling the blue print...
draw a center line...
at the origin...
make sure it's vertical...
and give it dimension...
you can see how small blue print actually is...
we will have to scale it up...
and position accurately...
go to the features properties of the blue print...
and make sure you have the Lock aspect ratio tool...
sorry ...option checked
now drag and position the nose at the origin...
use this marks to scale the blue print...
just drag it on the way up...
this could take a while. So, I will take you to the part where I have correctly positioned...
...this blue print
right, now I've placed this blue print correctly...
my dimension is coinciding with the dimension on the blue print...
I will zoom and show you how exactly I have done that
and the blue print is in the middle as well..
here's the origin...
and here you can see the nose of the predator...
okay...
place to next blue print...
we will need reference dimension...
so... in this case, we'll take the wingspan after predator...
... as a reference dimension
draw a horizontal line...
to measure the wingspan...
... in this blue print...
okay... this is about...
right, this looks correct...
and we will use this dimension to place the next blue print...
exit the sketch...
and let's place the front blue print.
open a new sketch...
on the front plane...
and...
draw a line...
to show the wingspan...
okay...
make sure the line is symmetric... from the origin...
and give the dimension of... to wingspan
now, we can import the blue print
and let's scale the blue print now...
place the wheel at the origin and in middle...
... like this
and then scale up...
sorry
okay, let me take you to the part where I have placed this blue print correctly...
okay... So, I have placed this blue print correctly as well...
and...
let's zoom in to show you exactly how...
blue print is in the middle...
and wingspan dimension is coinciding with the wings...
... edges of the wings..
see...
okay...
now we need another reference dimension to place the final blue print...
this should be a vertical dimension... so...
we will use the wingspan... line
... already drawn...
and...
we take it to the point where top shell of the fuselage line meets the bottom shell...
okay... see right here...
let's place it in the middle...
and...
dimension it...
okay this is about... 1.5 Meters
right now, we are ready to place the next blue print
exit the sketch...
and...
open new sketch in right plane...
okay... So, we have two reference dimensions...
let's draw this dimension...
make a horizontal line...
I have already coincided with the point from the previous sketch...
but... this should be 1500 Millimeters...
and...
this dimension would be...
from the first blue print...
let's import the blue print...
and we can start scaling it...
all over again...
okay... again this could take a while. so, let me take you to the part where I have placed this correctly as well...
okay, I have placed the final blue print...
and let me show you how...
this point is vertical with the origin...
and this line is 8.22 Meters...
and this line is 1500 Millimeters...
from the origin...
okay... let's exit this sketch
and rename the sketches...
okay, this point it'd be useful to save your work..
so, let's save it here...
right. Now we can starting modeling the body...
okay, what we are going to do is...
... model one half of the plane and then mirror it to the opposite side...
see, these are similar...
so, we will make this portion and... mirror it...
about the right plane...
to make the full body...
okay, we are into the right side again...
I can see that... I have to model this into different sections...
this portion right here of the Fuselage...
is a straight section almost...
so, model it with extruded surfaces... probably
and then model the section... which has curve
and then an other section that has final curve...
again... we will split the fuselage... into two portions
the top half and bottom half...
I have already told you about the top half, how we will model this...
and similarly... we will have the bottom half of the fuselage...
that we are going to model similarly...
from this portion to this portion round about...
we have straight section that we can model through extruded surfaces...
and then we have two curve portions...
okay. for the curve portion, we will need some helping surfaces...
and then we can use surface fill tool... to make the useful surfaces from helping surface...
let's begin...
okay... in the previous step, we made the helping planes which will help us model the fuselage...
I have already named this planes as such... we can copy this names...
okay...
so, at this point... it would be useful to make blue print slightly transparent...
so, right click on the sketch pictures...
and... click feature properties...
enable to transparency... and give it 50 % transparency...
so, do this for all the blue prints...
right, we can start modeling the top half of the fuselage...
and a tail section, which is the easiest one
okay... the first thing
which you will see here...
is that...
while we using... this line
from the right view... and
this line... from the top view
we do not have the cross section of the tail...
when I click at normal to the front...
we can see... we only have this section of the fuselage...
which is...
around this maximum section of the fuselage...
so, we have to slightly improvise to make the cross section, of this portion of the tail...
we will try to closely follow...
this portion...
while staying in the bounds of the lines of the fuselage...
... in this area of the tail...
let's begin...
okay... now we will model the panel of the fuselage between the mid and front mid plane...
we will do this by making helping surfaces...
one using this line... and the other
... using this line...
once we have made these helping surfaces...
we are going to...
... proximate this curve with this line...
and once we have made that curve...
we can make the useful panel...
between the mid and front mid plane...
right, now that we have the panel between front mid and mid plane...
... of the top of the fuselage...
we can start work on the front most panel...
of the top of the fuselage...
we will make this panel in similar manner... using this line... and this line
... to make helping surfaces...
then using the surface fill tool, we are going to extract the useful surface...
and this will complete the top of fuselage...
all right, let's begin...
right... now the top section on fuselage is complete...
we can... make the bottom in similar manner...
first, let's hide these helping surfaces...
we won't be needing them anymore...
okay... so, this is the useful portion of the top.
right, in making the bottom portion...
again, it will have to be modeled in three portions...
the first portion to tail portion will be straight...
but it ends till about here...
so, we will have to split these portion right here...
and... then the first curve edge begins...
from this point to here...
and then the third panel will start from here to here...
again in very similar fashion...
we will have to...
... improvise the cross section of the tail section...
we will try to make it something like this...
and...
that's all... let's begin
all right. one portion for the tail is complete...
and we can begin working on the remaining two panels...
... in a similar fashion...
by using helping surfaces...
we will make these two panels...
and... extract the useful surface
from the helping surfaces...
by the use of fill surface tool...
okay...
let's begin
all right. now we have our fuselage...
let's turn our attention to the wings...
let's first hide this surfaces... we don't need them anymore...
okay... for the wings...
I am going to generate some curves for these span-wise lines...
by using this line... this line...
and line that we are going to draw...
it should pass straight through in the middle of the wing...
then by using these curves...
... we are going to make surfaces...
okay...
the...
the... airfoil characteristics are not available in these blue prints... as you can see
you should have been able to see the airfoil on the right plane...
but it has no information about the wings...
so, we will improvise the shape of the airfoil...
and...
then we will have our wings...
let's begin
all right. now that we've made the wings...
we can turn our attention to something similar...
that is the rear wings or the stabilizers...
total of three stabilizers...
two horizontal and one vertical...
now, we have quite a bit of information for the horizontal stabilizers...
that is, we have the span, the direction... and we have width as well...
again, no airfoil characteristics...
so, we will have to improvise that...
okay... for the vertical stabilizer, we don't have much information...
you might just be able to see it here... the Hindu wheel...
that's just about it...
that's all the information we have for this...
so, we will slightly need to improvise our vertical stabilizers...
and we will make it in a similar manner...
to the wings...
we will generate curves... like this one
and this one...
and then we will use it to make surfaces...
using the cross section of the airfoil, that will improvise...
all right.... let's begin
all right. now that we have our stabilizers...
we can turn our attention to some other details...
... on the body...
for e.g. we have here...
...the
... air intake and exhaust for the engine of the propeller...
and also...
we have made tail slightly shorter...
we have only made it up untill...
the rear wings...
without to extend it further...
all the way to start of the propeller...
next...
we have an other arrow dynamic feature here...
now, I am not sure why this feature is displayed here...
because the MQ-1 predator...
has sort of a wing here...
so, we are going to make that wing...
and also an important feature, is the...
lemdat attaches the wing...
to the launcher of the hellfire missile...
we are going to make that now as well...
after that... we are going to delete the unnecessary surfaces...
and... we are going to mirror the body to make the complete shell...
all right... let's start
all right... now that we have the basic body of the predator...
we can begin work on propeller...
let me just bring back the planes and the sketches...
okay... you can see that we have few dimensions...
for the clown and the blades of the propeller...
we have the length of the blades...
and where they are situated horizontally with respective...
again... no aerodynamic characteristics of the propeller... plates...
so we will have to improvise on that account
okay...
let's start...
all right... some of you might be wondering why we made this blades of the rotor...
as solids...
there's a reason for it...
solid works... sub-sting module might not be as powerful as it's counterpart KTR...
so sometimes...
some of the features don't look very complex...
... tend to not execute properly
and I will give you example right now...
so, if i was to make this with surfacing, what I would do is...
I would make this portion...
with surface loft
and...
afterwards... I would do is...
I'd make fill surface...
right here...
make it tangent...
and... we'd have tip of the rotor...
this looks much better than the other tip... that we domed...
okay...
so, this feature... we made successfully
now let's try it on the other blade or first blade...
again...
this was a loft... and...
I am going to make the tip of the blade...
... and this time
it's going to give me an error...
I don't know what the official name for this is...
but...
I call it the boot line algorithm... problem
so... yeah
sometime you just have to...
live with the few things that solid works does not have capabilities to do...
and...
we will leave the fence... sorry the blades...
as solids...
like this...
I think it would be more useful to...
at this point...
convert the whole model...
to a solid...
and make the rest of the features as solid as well...
that would be more convenient...
right... let's begin
right... with mirror basic features fulled the body
this includes... some mirror dynamic features that we made in this step
we made a wing light...
also... we added socket for the camera
this camera... we are going to make later on...
okay...
the next step is to add few appearance features...
this would include adding fillets...
changing colors of the surfaces...
and...
adding logos...
so, let's start...
okay... so we have completed the body of predator...
in this last step, we have added some appearance features...
like the fillets... to make it looks smooth and neat...
and we also changed the color of few things like light and tip of the blades...
okay... and then the major portion...
how to add logos...
we have looked at some techniques like tracing of pictures...
with the help of sketch tool...
then we have looked at how you can actually add text...
and... also
how you can use the auto-trace feature...
now... the auto-trace feature usually works with high resolution image. so...
if you have low resolution image, don't expect much from this feature...
also making sketch blocks are really helpful...
you can make sketch blocks and reuse them again and again...
... in terms of logos...
it's really helpful. so, you don't have to make logo over and over again...
so...
this concludes the body of the predator...
we will move on to other features now...
so, now that we have completed predator body...
it's time to turn our attention to the second most important component in this tutorial...
the hellfire missile...
again... to use the similar technique as we used before...
... to make this missile...
... tracing from the blue print as you can see here...
and... it's time again to model the hellfire missile...
... as solid from start to end...
cause we don't really need the flexibility of the surface tool...
so...
let's start making the hellfire missile...
okay... after a first step...
we have the basic shape and size of the hellfire missile...
now before we move on to the next step...
I just wanted to tell you a few things...
about the next set of instructions...
now the important thing I want to highlight...
... is that different techniques I have used to make these loft 9 and loft 16...
now, let's first go to the loft 9...
what have I actually done here is that...
I have traced a few curves on the surface...
on this cylindrical surface of the missile...
and another 2D sketch...
... some point above...
the main cylinder of the missile...
and... I've used loft technique to combine the two...
okay...
now... this technique might be proven to some failures...
make for example...
when I try to accurate the merge tangent faces...
...option. it gives me an error...
the reason why solidworks does that...
... is because, it is having trouble combining this face...
this sketch that we have drawn... these three sketches...
... with the circular surface of the cylinder...
so, it might not always give you correct results.
sometimes it might even fail to merge the results...
that is... merge this loft with the main cylinder...
keep this one for now.
so...
if this technique fails for you...
then you can always use the technique that we have used to make loft 16...
now in addition to the two sketches...
one on the surface of the cylinder...
... and one above that
we have also added a third sketch...
that is the...
this sketch...
as inside the cylinder...
and this way...
you can see
that...
solidworks does not have any drawback...
making this loft and...
combining or...
... solving this loft with respective to the main cylinder...
so, if you're having trouble making loft 9...
... with the technique shown for loft 9...
you can always use technique used in loft 16...
to make loft 9 as well...
you see that these techniques are quite similar...
and it's just uses feature...
... that have already been made
in the course of the tutorial...
so...
let's begin...
all right...
so, that's pretty much wraps up the hellfire missile...
we've made some features like the fans...
and then we have several control fans for guidance that people wants...
right here...
some appearance feature as well like transparency and different colors...
then we have made the ports...
for the launcher attachment...
so, this pretty much wraps up the hellfire missile...
okay...
next, we have to make the launcher for the hellfire missile...
now, we don't exactly have the blue prints...
but we will try to make it something like this...
we will have to improvise most of our features...
but hopefully...
we will end up...
... making something like this...
so...
let's begin...
all right. this wraps up the launcher...
now, most of the features are pretty simple...
you have extrudes and cut extruded
most challenging feature by far... was the fillet
now, mate this fillets using a predetermined order...
it's usually not that simple...
what happen is...! that...
when there are lot of edges combining at a single point...
... solidworks sometimes can not solve those fillets in a single step...
so... you have to make few steps... of fillets
... to get the correct fillets...
and get fillets at all sometimes
there's another alternative to this...
... if you are looking to the pattern.
what you can do is...
you can go to the fillet...
and you can go to the fillet expert...
now...
if it doesn't show you right away...
... the preview
that means that fillets...
... all the fillet will not be resolved
but if you select all the edges you want to fillet...
and... click the apply button
solidworks will automatically determine which edges it can solve...
and which edges it can not solve...and make fillet for you.
so, you can try this option as well...
okay... another thing that you should keep in mind...
just if you are not following exact dimension as I am...
this feature right here...
this is the feature...
... that we made for the attachment point of the launcher with predator body...
this... the dimension of this feature should be... same as the feature we made underneath the wing...
... the two holes actually. so, make sure that diameters and center to center distance is correct with respect to predator body...
also...
another feature here...
this real type thing...
this is actually used to mount the hellfire missile...
so... the dimension of this feature should be the same as the...
... the guarding point we made on hellfire missile...
... make sure of this and...
you should be good...
okay...
let's save this... and
... now we are ready to make multitargeting system turret...
and the multi targeting system itself...
so...
let's start with that...
okay...
this was simple enough...
just one thing we should make sure of...
... is this diameter 405 Millimeters...
this should be the same as sock
…
and welcome to this tutorial...!
this tutorial is for making the MQ-1 Predator and solidworks...
now, we will make the predator and different parts...
first, we will start with body
and... using blue prints and surfacing tools mostly...
we will make the body of predator...
afterwards...
we are going to model the Hellfire Missile...
after that...
we are going to make the launcher for the Hellfire Missile...
after that...
we will make the...
... targeting system for the MQ-1 predator...
this is also in two parts...
here we have the Turret...
for the MTS... and then the MTS itself...
fine... we are going to assemble all of these components...
and end up with this assembly...
so... let's begin...
right, let's start with the body of the UAV...
open a new part...
and select the correct units...
now the first that we will have to do...
... is to place the blue prints on these three planes...
let's start with the top one...
open a new sketch in the top plane...
and go to tools... sketch tools...
and sketch pictures...
put blue print...
... and select yes
now we need a reference dimension, to be able to scale the blue print...
and we will use this dimension of 8.22 meters...
... as a reference for scaling the blue print...
draw a center line...
at the origin...
make sure it's vertical...
and give it dimension...
you can see how small blue print actually is...
we will have to scale it up...
and position accurately...
go to the features properties of the blue print...
and make sure you have the Lock aspect ratio tool...
sorry ...option checked
now drag and position the nose at the origin...
use this marks to scale the blue print...
just drag it on the way up...
this could take a while. So, I will take you to the part where I have correctly positioned...
...this blue print
right, now I've placed this blue print correctly...
my dimension is coinciding with the dimension on the blue print...
I will zoom and show you how exactly I have done that
and the blue print is in the middle as well..
here's the origin...
and here you can see the nose of the predator...
okay...
place to next blue print...
we will need reference dimension...
so... in this case, we'll take the wingspan after predator...
... as a reference dimension
draw a horizontal line...
to measure the wingspan...
... in this blue print...
okay... this is about...
right, this looks correct...
and we will use this dimension to place the next blue print...
exit the sketch...
and let's place the front blue print.
open a new sketch...
on the front plane...
and...
draw a line...
to show the wingspan...
okay...
make sure the line is symmetric... from the origin...
and give the dimension of... to wingspan
now, we can import the blue print
and let's scale the blue print now...
place the wheel at the origin and in middle...
... like this
and then scale up...
sorry
okay, let me take you to the part where I have placed this blue print correctly...
okay... So, I have placed this blue print correctly as well...
and...
let's zoom in to show you exactly how...
blue print is in the middle...
and wingspan dimension is coinciding with the wings...
... edges of the wings..
see...
okay...
now we need another reference dimension to place the final blue print...
this should be a vertical dimension... so...
we will use the wingspan... line
... already drawn...
and...
we take it to the point where top shell of the fuselage line meets the bottom shell...
okay... see right here...
let's place it in the middle...
and...
dimension it...
okay this is about... 1.5 Meters
right now, we are ready to place the next blue print
exit the sketch...
and...
open new sketch in right plane...
okay... So, we have two reference dimensions...
let's draw this dimension...
make a horizontal line...
I have already coincided with the point from the previous sketch...
but... this should be 1500 Millimeters...
and...
this dimension would be...
from the first blue print...
let's import the blue print...
and we can start scaling it...
all over again...
okay... again this could take a while. so, let me take you to the part where I have placed this correctly as well...
okay, I have placed the final blue print...
and let me show you how...
this point is vertical with the origin...
and this line is 8.22 Meters...
and this line is 1500 Millimeters...
from the origin...
okay... let's exit this sketch
and rename the sketches...
okay, this point it'd be useful to save your work..
so, let's save it here...
right. Now we can starting modeling the body...
okay, what we are going to do is...
... model one half of the plane and then mirror it to the opposite side...
see, these are similar...
so, we will make this portion and... mirror it...
about the right plane...
to make the full body...
okay, we are into the right side again...
I can see that... I have to model this into different sections...
this portion right here of the Fuselage...
is a straight section almost...
so, model it with extruded surfaces... probably
and then model the section... which has curve
and then an other section that has final curve...
again... we will split the fuselage... into two portions
the top half and bottom half...
I have already told you about the top half, how we will model this...
and similarly... we will have the bottom half of the fuselage...
that we are going to model similarly...
from this portion to this portion round about...
we have straight section that we can model through extruded surfaces...
and then we have two curve portions...
okay. for the curve portion, we will need some helping surfaces...
and then we can use surface fill tool... to make the useful surfaces from helping surface...
let's begin...
okay... in the previous step, we made the helping planes which will help us model the fuselage...
I have already named this planes as such... we can copy this names...
okay...
so, at this point... it would be useful to make blue print slightly transparent...
so, right click on the sketch pictures...
and... click feature properties...
enable to transparency... and give it 50 % transparency...
so, do this for all the blue prints...
right, we can start modeling the top half of the fuselage...
and a tail section, which is the easiest one
okay... the first thing
which you will see here...
is that...
while we using... this line
from the right view... and
this line... from the top view
we do not have the cross section of the tail...
when I click at normal to the front...
we can see... we only have this section of the fuselage...
which is...
around this maximum section of the fuselage...
so, we have to slightly improvise to make the cross section, of this portion of the tail...
we will try to closely follow...
this portion...
while staying in the bounds of the lines of the fuselage...
... in this area of the tail...
let's begin...
okay... now we will model the panel of the fuselage between the mid and front mid plane...
we will do this by making helping surfaces...
one using this line... and the other
... using this line...
once we have made these helping surfaces...
we are going to...
... proximate this curve with this line...
and once we have made that curve...
we can make the useful panel...
between the mid and front mid plane...
right, now that we have the panel between front mid and mid plane...
... of the top of the fuselage...
we can start work on the front most panel...
of the top of the fuselage...
we will make this panel in similar manner... using this line... and this line
... to make helping surfaces...
then using the surface fill tool, we are going to extract the useful surface...
and this will complete the top of fuselage...
all right, let's begin...
right... now the top section on fuselage is complete...
we can... make the bottom in similar manner...
first, let's hide these helping surfaces...
we won't be needing them anymore...
okay... so, this is the useful portion of the top.
right, in making the bottom portion...
again, it will have to be modeled in three portions...
the first portion to tail portion will be straight...
but it ends till about here...
so, we will have to split these portion right here...
and... then the first curve edge begins...
from this point to here...
and then the third panel will start from here to here...
again in very similar fashion...
we will have to...
... improvise the cross section of the tail section...
we will try to make it something like this...
and...
that's all... let's begin
all right. one portion for the tail is complete...
and we can begin working on the remaining two panels...
... in a similar fashion...
by using helping surfaces...
we will make these two panels...
and... extract the useful surface
from the helping surfaces...
by the use of fill surface tool...
okay...
let's begin
all right. now we have our fuselage...
let's turn our attention to the wings...
let's first hide this surfaces... we don't need them anymore...
okay... for the wings...
I am going to generate some curves for these span-wise lines...
by using this line... this line...
and line that we are going to draw...
it should pass straight through in the middle of the wing...
then by using these curves...
... we are going to make surfaces...
okay...
the...
the... airfoil characteristics are not available in these blue prints... as you can see
you should have been able to see the airfoil on the right plane...
but it has no information about the wings...
so, we will improvise the shape of the airfoil...
and...
then we will have our wings...
let's begin
all right. now that we've made the wings...
we can turn our attention to something similar...
that is the rear wings or the stabilizers...
total of three stabilizers...
two horizontal and one vertical...
now, we have quite a bit of information for the horizontal stabilizers...
that is, we have the span, the direction... and we have width as well...
again, no airfoil characteristics...
so, we will have to improvise that...
okay... for the vertical stabilizer, we don't have much information...
you might just be able to see it here... the Hindu wheel...
that's just about it...
that's all the information we have for this...
so, we will slightly need to improvise our vertical stabilizers...
and we will make it in a similar manner...
to the wings...
we will generate curves... like this one
and this one...
and then we will use it to make surfaces...
using the cross section of the airfoil, that will improvise...
all right.... let's begin
all right. now that we have our stabilizers...
we can turn our attention to some other details...
... on the body...
for e.g. we have here...
...the
... air intake and exhaust for the engine of the propeller...
and also...
we have made tail slightly shorter...
we have only made it up untill...
the rear wings...
without to extend it further...
all the way to start of the propeller...
next...
we have an other arrow dynamic feature here...
now, I am not sure why this feature is displayed here...
because the MQ-1 predator...
has sort of a wing here...
so, we are going to make that wing...
and also an important feature, is the...
lemdat attaches the wing...
to the launcher of the hellfire missile...
we are going to make that now as well...
after that... we are going to delete the unnecessary surfaces...
and... we are going to mirror the body to make the complete shell...
all right... let's start
all right... now that we have the basic body of the predator...
we can begin work on propeller...
let me just bring back the planes and the sketches...
okay... you can see that we have few dimensions...
for the clown and the blades of the propeller...
we have the length of the blades...
and where they are situated horizontally with respective...
again... no aerodynamic characteristics of the propeller... plates...
so we will have to improvise on that account
okay...
let's start...
all right... some of you might be wondering why we made this blades of the rotor...
as solids...
there's a reason for it...
solid works... sub-sting module might not be as powerful as it's counterpart KTR...
so sometimes...
some of the features don't look very complex...
... tend to not execute properly
and I will give you example right now...
so, if i was to make this with surfacing, what I would do is...
I would make this portion...
with surface loft
and...
afterwards... I would do is...
I'd make fill surface...
right here...
make it tangent...
and... we'd have tip of the rotor...
this looks much better than the other tip... that we domed...
okay...
so, this feature... we made successfully
now let's try it on the other blade or first blade...
again...
this was a loft... and...
I am going to make the tip of the blade...
... and this time
it's going to give me an error...
I don't know what the official name for this is...
but...
I call it the boot line algorithm... problem
so... yeah
sometime you just have to...
live with the few things that solid works does not have capabilities to do...
and...
we will leave the fence... sorry the blades...
as solids...
like this...
I think it would be more useful to...
at this point...
convert the whole model...
to a solid...
and make the rest of the features as solid as well...
that would be more convenient...
right... let's begin
right... with mirror basic features fulled the body
this includes... some mirror dynamic features that we made in this step
we made a wing light...
also... we added socket for the camera
this camera... we are going to make later on...
okay...
the next step is to add few appearance features...
this would include adding fillets...
changing colors of the surfaces...
and...
adding logos...
so, let's start...
okay... so we have completed the body of predator...
in this last step, we have added some appearance features...
like the fillets... to make it looks smooth and neat...
and we also changed the color of few things like light and tip of the blades...
okay... and then the major portion...
how to add logos...
we have looked at some techniques like tracing of pictures...
with the help of sketch tool...
then we have looked at how you can actually add text...
and... also
how you can use the auto-trace feature...
now... the auto-trace feature usually works with high resolution image. so...
if you have low resolution image, don't expect much from this feature...
also making sketch blocks are really helpful...
you can make sketch blocks and reuse them again and again...
... in terms of logos...
it's really helpful. so, you don't have to make logo over and over again...
so...
this concludes the body of the predator...
we will move on to other features now...
so, now that we have completed predator body...
it's time to turn our attention to the second most important component in this tutorial...
the hellfire missile...
again... to use the similar technique as we used before...
... to make this missile...
... tracing from the blue print as you can see here...
and... it's time again to model the hellfire missile...
... as solid from start to end...
cause we don't really need the flexibility of the surface tool...
so...
let's start making the hellfire missile...
okay... after a first step...
we have the basic shape and size of the hellfire missile...
now before we move on to the next step...
I just wanted to tell you a few things...
about the next set of instructions...
now the important thing I want to highlight...
... is that different techniques I have used to make these loft 9 and loft 16...
now, let's first go to the loft 9...
what have I actually done here is that...
I have traced a few curves on the surface...
on this cylindrical surface of the missile...
and another 2D sketch...
... some point above...
the main cylinder of the missile...
and... I've used loft technique to combine the two...
okay...
now... this technique might be proven to some failures...
make for example...
when I try to accurate the merge tangent faces...
...option. it gives me an error...
the reason why solidworks does that...
... is because, it is having trouble combining this face...
this sketch that we have drawn... these three sketches...
... with the circular surface of the cylinder...
so, it might not always give you correct results.
sometimes it might even fail to merge the results...
that is... merge this loft with the main cylinder...
keep this one for now.
so...
if this technique fails for you...
then you can always use the technique that we have used to make loft 16...
now in addition to the two sketches...
one on the surface of the cylinder...
... and one above that
we have also added a third sketch...
that is the...
this sketch...
as inside the cylinder...
and this way...
you can see
that...
solidworks does not have any drawback...
making this loft and...
combining or...
... solving this loft with respective to the main cylinder...
so, if you're having trouble making loft 9...
... with the technique shown for loft 9...
you can always use technique used in loft 16...
to make loft 9 as well...
you see that these techniques are quite similar...
and it's just uses feature...
... that have already been made
in the course of the tutorial...
so...
let's begin...
all right...
so, that's pretty much wraps up the hellfire missile...
we've made some features like the fans...
and then we have several control fans for guidance that people wants...
right here...
some appearance feature as well like transparency and different colors...
then we have made the ports...
for the launcher attachment...
so, this pretty much wraps up the hellfire missile...
okay...
next, we have to make the launcher for the hellfire missile...
now, we don't exactly have the blue prints...
but we will try to make it something like this...
we will have to improvise most of our features...
but hopefully...
we will end up...
... making something like this...
so...
let's begin...
all right. this wraps up the launcher...
now, most of the features are pretty simple...
you have extrudes and cut extruded
most challenging feature by far... was the fillet
now, mate this fillets using a predetermined order...
it's usually not that simple...
what happen is...! that...
when there are lot of edges combining at a single point...
... solidworks sometimes can not solve those fillets in a single step...
so... you have to make few steps... of fillets
... to get the correct fillets...
and get fillets at all sometimes
there's another alternative to this...
... if you are looking to the pattern.
what you can do is...
you can go to the fillet...
and you can go to the fillet expert...
now...
if it doesn't show you right away...
... the preview
that means that fillets...
... all the fillet will not be resolved
but if you select all the edges you want to fillet...
and... click the apply button
solidworks will automatically determine which edges it can solve...
and which edges it can not solve...and make fillet for you.
so, you can try this option as well...
okay... another thing that you should keep in mind...
just if you are not following exact dimension as I am...
this feature right here...
this is the feature...
... that we made for the attachment point of the launcher with predator body...
this... the dimension of this feature should be... same as the feature we made underneath the wing...
... the two holes actually. so, make sure that diameters and center to center distance is correct with respect to predator body...
also...
another feature here...
this real type thing...
this is actually used to mount the hellfire missile...
so... the dimension of this feature should be the same as the...
... the guarding point we made on hellfire missile...
... make sure of this and...
you should be good...
okay...
let's save this... and
... now we are ready to make multitargeting system turret...
and the multi targeting system itself...
so...
let's start with that...
okay...
this was simple enough...
just one thing we should make sure of...
... is this diameter 405 Millimeters...
this should be the same as sock
…